Why does my washer keep saying LoC?
Why does my washer keep saying LoC?
If the control lock has been activated, the control will not function. If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.
How do I clear the LoC on my Whirlpool washer?
If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.
What do you do when your washer says LoC?
Press and hold for 3 seconds the “Control Lock/Unlock” button on the control panel to unlock the control panel. The “Control Lock” status light is goes out when the control panel is unlocked. In addition to Oldturkeys answer, try unplugging it for five minutes to allow it to reset.
What does loc mean on my tumble dryer?
Control Lock
The Loc Error code indicates that the Control Lock has been enabled. When the control is locked, the dryer will not start or operate. Some models will look like the following: Press and hold the Control Lock Key for 3 seconds to unlock the machine.
Why does my Kenmore washer say Loc?
The “LOC” error indicates that the door lock is stuck and the machine is unable to lock or unlock the door. If the machine cannot lock the door, it will not begin the washing cycle. If it is unable to unlock the door, you cannot access your laundry at the end of the washing cycle.
How do I fix the Control Lock on my Whirlpool Duet dryer?
How to Unlock the Controls for a Whirlpool Duet Washer
- Locate the “Control Lock/Unlock” button on your Duet’s control panel.
- Press and hold the “Control Lock/Unlock” button for three seconds.
- Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.
How do you unlock a dryer?
To lock and unlock the dryer controls: Press and hold the Extended Tumble and – (minus) buttons for 3 seconds. The control lock icon will flash while locking/unlocking, stay on when locked, and turn off when unlocked.
What should I do if my Loc is flashing?
@treeplanter LOC is a reference to the control lock. Two ways you can try to fix it. The normal procedure is to hold down the “end of cycle signal” (drain/spin)button for 3 to 5 seconds. Or you can try to press and hold the add steam button for 5 seconds. Sometimes a simple unplugging the machine for 15minutes will reset it as well.
What does Loc on a front load washer mean?
I attached the link below. Hope this helps! The letters (LOC) indicates Controls are Locked. To avoid having someone accidentally start or stop the washer, press OPTIONS and SELECT at the same time until the Control (Control Lock) indicator is lighted.
Where is the LOC code on my Maytag front load washer?
Red flashing key on left of display and L oc when trying to Red flashing key on left of display and L oc when trying to start washer. read more Mark M Home Appliance Technician Bachelors 5,324 satisfied customers Front loading washer (WFW5620HW0) has loc error code in
When does a whirlpool washer show a LOC code?
A Whirlpool Washer displays a LOC error code when a Control Lock On has been detected by the internal electronic diagnostics.
@treeplanter LOC is a reference to the control lock. Two ways you can try to fix it. The normal procedure is to hold down the “end of cycle signal” (drain/spin)button for 3 to 5 seconds. Or you can try to press and hold the add steam button for 5 seconds. Sometimes a simple unplugging the machine for 15minutes will reset it as well.
Red flashing key on left of display and L oc when trying to Red flashing key on left of display and L oc when trying to start washer. read more Mark M Home Appliance Technician Bachelors 5,324 satisfied customers Front loading washer (WFW5620HW0) has loc error code in
Why is the LOC door flashing on my Wall Oven?
If “LOC DOOR” is flashing in the display of your range or wall oven and the self-clean cycle has not been selected, first, check to make sure the Control Lockout feature was not engaged. Consult your Owner’s Manual for directions specific to your model. Download a copy of your Owner’s Manual
A Whirlpool Washer displays a LOC error code when a Control Lock On has been detected by the internal electronic diagnostics.
