What does PF mean on a Whirlpool stove

PF – Power Failure – PF error code indicates a power failure during the dryer’s cycle. Press and HOLD start to continue the cycle, or press off/pause to clear display.

How do I fix the PF on my Whirlpool oven?

Power the unit down by turning off the circuit breaker(s) or fuse(s) for one (1) minute.
Power the unit up by turning on the circuit breaker(s) or fuses(s),
Monitor the the product for one (1) minute to ensure the error code does not return.

Why does my stove say PF?

The “PF” indicates a power failure. This would be normal to happen when the circuit breaker was flipped OFF and back ON. The “Clock” must be set before all the other functions will be available. You will need to press “Clock” and set the clock and your oven should operate normally.

What does PF mean on a gas range?

The PF message in the display usually indicates a power failure. Try resetting the control by disconnecting power for 30-60 seconds or press stop/cancel.

How do I reset my Whirlpool electric stove?

Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Start a bake cycle.
Monitor the oven for one (1) minute to ensure the error code does not display again.
Verify oven operation.

How do I put my Whirlpool oven in diagnostic mode?

Enter Diagnostics mode by pressing CANCEL>CANCEL>START within a 5-second period. Entering Diagnostics mode will cancel any active oven operation. Enter the Diagnostics mode only after the oven is cool. All elements (depending on which cycle is being used) will operate with the oven door open.

What does F1 mean on Whirlpool oven?

If you receive a two-digit error code reading F1, your Whirlpool range may be experiencing one of three problems. There may be an analog to digital failure; if this is the case, simply disconnect the range for 30 seconds and plug back in. If the same display reappears, you may need to replace the control board.

How do I reset my oven?

Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.

How do I reset my Whirlpool oven after a power cut?

Look for “Control Lock” on the oven control console and then reset by typically holding the button(s) for 3 seconds.

What does PF mean on a GE oven?

PF – Power Failure – Select ‘cancel’ to clear code. If error persists, check electrical connections to dishwasher and electronic control (control board). Replace if defective.

Article first time published on

What does PF mean on a Whirlpool washer?

A PF (Power Failure) error code indicates that the wash cycle was interrupted by a power failure. Touch and hold START to restart the washer cycle or press POWER to clear the display.

How do you unlock the control panel on a Whirlpool stove?

Press and hold on to the lock for 3 seconds to lock the control panel. The light above the lock will turn on. Press and hold LOCK for 3 seconds to open the control panel.

Why is my Whirlpool stove not heating?

The igniter is the most commonly defective part for an oven not heating. … Second, the igniter gets hot enough to glow and ignite the gas in the oven burner. If the igniter gets weak, it will fail to open the safety valve correctly. If the valve does not open, the oven will not heat.

How do you reset a stove after a power outage?

If a recent power outage has occurred, turn off the household circuit breaker for the range for one (1) minute. Then reset the circuit breaker and monitor the range for one (1) minute to ensure the error code does not display again. Verify range operation is normal.

How do I fix F1 error on stove?

You can try resetting the range by disconnecting it from the outlet or switching off the circuit breaker of the home for 10-20 minutes then restore the power. If the reset doesn’t work your range may have one of the above failures.

How do I fix F1 error on my oven?

On some models it is possible that F1 could also be caused by a keypad problem. In this case it will specify in the tech sheet to power down the oven, disconnect the keypad then power the oven back on, wait for a few minutes to see if the error reappears. If the error reappears it is definitely the control board.

Why does my stove say F1?

The F1 error means that there is an electronics failure within the oven. This failure can occur within the keypad itself, the electronic oven control or the oven temperature sensor. … The error can also indicate data corruption within the oven’s electronic controller.

What does F5 mean on a Whirlpool oven?

The F5 on most Whirlpool ranges will indicate that you have a problem with the oven door latch assembly or the oven door switch. Since you are seeing this error code when you are trying to set the self cleaning mode, this is likely the problem with your range. You could have a problem with the door switch.

What are the symbols on an electric oven?

Fan oven symbol. The standard setting for many electric fan-assisted ovens shows a fan, often inside a circle. …
CircoTherm® symbol. …
Circo-roasting/grill with fan symbol. …
Bottom heat symbol. …
Top and bottom heat symbol. …
Pizza symbol (fan with bottom heat) …
Bread baking symbol. …
Slow cooking symbol.

What does CLR mean on Whirlpool oven?

You don’t mention any other problems or if you can select and change cycles but “CLR” is short for “Clear” and would indicate a problem with the over control. Check if the control lock is turned on by pressing and holding the “Start” keypad for 3 seconds and see if the “Loc” light goes out or comes on.

Can a power surge damage an oven?

Electric appliances are sensitive to power surges and often experience some damage as a result. When you experience a power outage, there is often a surge at the beginning or after the power is restored. This surge can disrupt your oven’s internal settings and even fry some of the wirings.

Why is the oven beeping?

When the oven beeps, it is to alert the user that the food is complete. Some models will continue to beep as a reminder to take the food out of the oven. Convection ovens also sometimes include a temperature gauge that will cause the oven to beep when it’s at 75% of the original cooking time.

Will electric oven turn back on after power outage?

If the electric oven is controlled by a digital timer or digital controls then it’s unlikely that it will turn back on after a power outage. However analog timers and manual controls will probably remain in the ON position and will restore power to the oven when power is restored.

How do I reset my oven control board?

But the first thing you should do is try to perform a hard reset by unplugging the oven, waiting about 30 seconds, and then plugging it back in again. In some cases, this will be enough to reset the control board and get your oven working again.

Why is my stove top working but not my oven?

In most common cases, this specific issue means that the broil element and the baking element remain functional. However, there’s probably a blown internal fuse. If it’s not the fuse, it could be the temperature sensor, broken or frayed wiring, or even a breakdown of the oven control board.

Why is my oven on but not heating up?

This can be caused by a faulty temperature sensor or a temperature sensor that is touching the wall of the oven. … Cause: If it’s still not heating to the correct temperature and you’ve checked or replaced the heating elements, gas igniter and temperature sensor, it may simply need to be calibrated.

What does PF error code mean?

A PF (Power Failure) error code indicates that the drying cycle has been interrupted by a power failure. … During a power outage, if there was an unexpected amount of power supply line “noise” that the control detected as an incorrect voltage amount, the control could display the PF Error Code.

How do you fix microwave PF?

Touch the “Clear” pad if you see “PF” or “8888” on the control display panel. …
Press “Cancel” or “Clear/Off” if you see an “F” code displayed on your microwave. …
Program the cooking function, which should clear the displayed codes.

What does PF stand for on a GE microwave?

If a power failure should occur, a microwave, depending on the model, may display a “PF”, “888” or “8888” code. It is possible to see this display upon initial installation or after power was restored due to a power failure. Both display codes can be cancelled and normal operation resumed by touching the CLEAR pad.

How do I fix the PF code on my Whirlpool washer?

The PF Error code indicates that the unit has experienced a power failure during operation. Some models may allow you to hit “Start” to complete the cycle. For other models, you may need to hit “Cancel” and restart the machine from the beginning.

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.