How long does a chlorinator cell last

This is all possible thanks to your pool’s salt chlorine generator cell. With proper care, a cell will last about five years. Eventually, though, it will need to be replaced. The trick is, it’s not always easy to know when it’s time.

When should I replace my chlorinator cell?

How long should a salt cell last? The answer really depends on the use conditions and how often you do maintenance on your pool. The safe answer is that they usually last for about five to seven years. Salt Cells cost between $200 and $900 to replace, depending on your chlorinator model.

How do I know if my salt cell is not working?

1. Low chlorine levels in the pool water.
2. No Flow indication on the flow monitor.
3. Corroded plates.
4. Indicator lights signaling cell damage.

How often do salt cells need to be replaced?

Generally, a salt cell lasts for about 10,000 hours, which is usually around five years for most home pool owners. If your cell is close to or exceeds the 10,000-hour mark, and you notice any of the above signs, it could very well need replacement.

How much does it cost to replace a salt cell?

A well-maintained salt chlorine generator will last 3–7 years. Replacing the salt cell costs $700–$1100. Replacing the control board costs $500–$900. You can extend the lifespans by maintaining a consistent salt level, cleaning the cell only when needed, and using the reverse polarity function.

How long will a salt cell last?

This is all possible thanks to your pool’s salt chlorine generator cell. With proper care, a cell will last about five years. Eventually, though, it will need to be replaced.

How do I know if my salt cell pool is bad?

“Check salt” light on power center indicates problem but a routine water sample inspection shows salt levels are fine. Power center’s “Cell warning” light comes on and turns off after a cleaning but back on soon afterward. Voltage (higher than normal) and amperage (usually zero) level will show irregular readings.

Should I remove salt cell for winter?

It’s best to remove the salt cell for winter. Start by turning off all circuits to pool equipment, including the pool pump. Unscrew the unions to disconnect the generator cell from the pool lines. You can replace it with a temporary “dummy” cell to keep the line properly spaced and sealed through the winter.

How often should I clean my chlorinator cell?

At the very least, your saltwater chlorinator should be cleaned twice a year, but you should inspect it every two months just to be sure. If it needs to be cleaned, clean it. If it doesn’t, then just give it a good rinse with a garden hose.

Why does my salt water pool have no chlorine?

Salinity. Chlorine generators need salt to produce chlorine and can’t do so if the amount of salt in the water is too low. The desired salinity level in a saltwater pool is between 2,500 and 3,500 ppm. … If your salinity is below 2,500 ppm, the generator will not be able to produce chlorine.

Article first time published on

What percentage should my salt cell be set at?

We suggest you start your salt chlorine generator at 50 percent output and run it for a couple of days, then check the chlorine level. In a balanced pool, a good chlorine level is 1-3 parts per million. If your chlorine levels are low, you can raise the percentage, and if it’s high you can lower the percentage.

What causes a salt cell to fail?

Salt cells fail for a few different reasons, the main reason being lack of proper maintenance. It is very important to check the cell regularly for excessive buildup. … Use a cleaning kit designed for salt cells to keep the plates clear of buildup. Another common cause of salt cell failure is improper water balance.

What is a chlorinator cell?

The chlorinator cell consists of parallel titanium plates coated with ruthenium and iridium (precious metals from the platinum group of metals). The control box sends a safe electrical DC charge to the cell. As pool water passes through the salt cell, the salt in the water is turned into Hypochlorous acid.

Is it worth converting to saltwater pool?

Saltwater pools are cheaper to maintain in the short term: Annual costs to maintain a saltwater pool tend to be lower than annual costs to maintain a traditional chlorine pool. … There’s no chlorine smell: The strong chlorine smell that’s often present in a chlorine pool will not be a problem in a salt pool.

What is the best salt water chlorinator on the market?

1. Pentair 520555 IntelliChlor Salt Chlorine Generator – Best Overall. …
2. NeXa Chlor Pool Salt Chlorine Generator – Best Value. …
3. Hayward W3AQR15 Electronic Salt Chlorination System – Premium Choice. …
4. Solaxx CLG10A Saltron Retro Self Cleaning Salt Chlorine Generator.

How do you clean a Zodiac salt Cell?

1. Switch off the filter pump and chlorinator and close the necessary valves.
2. Unplug the cell terminal cap.
3. Unscrew the electrode retaining ring and remove the electrode.
4. Immerse the electrode in self-cleaning solution ensuring that the terminals are not immersed.

Can a salt cell be repaired?

Salt chlorine generators require some maintenance and repair. … Chances are at some point you will face an expensive repair to your salt system, either a new salt cell, or a new control board. Both of these repairs can approach half the cost of a new system.

How long should I run my salt chlorinator?

Run your system to run for 8-12 hours a day and set the chlorine output on the generator to 50%. After testing and determining the free chlorine readings over a few days, adjust the output on the generator only.

How do you clean an acid chlorinator cell?

Make a cleaning mixture of 1/10 parts Hydrochloric Acid to water (always add Hydrochloric acid to water). Turn the filtration system off. Remove Salt Cell from the housing. Add the Salt Cell to the cleaning mixture making sure there is little to no contact with the terminals.

Do you have to drain a saltwater pool every year?

You definitely need to drain some water from the pool when salinity reaches a 6,000 ppm level. Most salt water pools should be maintained with a salinity level of 2,500-4,000 ppm. The amount you drain depends on how elevated salinity levels are.

Are salt water pools less likely to freeze?

Do saltwater pools freeze? Yes, although their freezing point is just a bit lower than regular chlorinated water. Salt water pools freeze usually freeze closer to 28 degrees as opposed to 32, but nonetheless, they still freeze. So, treat it just like any other pool.

Can too much salt damage chlorinator?

Incorrect amounts can lead to unfortunate problems. Having too much salt in your pool water can result in unnecessarily increasing chemical expenses. But having too little salinity restricts the amount of chlorine being generated and can lead to algae and bacteria growth.

What does baking soda do for a pool?

Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.

Why is my salt water pool pH always high?

An unnaturally high pH level in your salt water pool could be a sign that your salt cell has been shortened due to running for an overly long period of time. Check the level of your cyanuric acid to be sure. The level should be between 80 and 100 ppm.

Can you add too much salt to a pool?

The salt level in your swimming pool should be 3,000 ppm (parts per million). Over-salting will not damage your pool system, but will create salty-tasting water. Highly excessive Salinity levels (over 6,000 ppm) will cause corrosion damage to metallic equipment, such as ladders and handrails.

What should my chlorinator read?

On a Hayward Salt Chlorinator, your salt reading should be between 2,700 – 3,400 PPM (parts per million) with the optimum level of 3,200 PPM.

Is it bad to run your pool pump 24 hours a day?

Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. … If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.

How do I get rid of salt cells in my pool?

1. Turn off the power to the system and deactivate the pool pump before removing the Turbo Cell.
2. Remove the Turbo Cell. …
3. If deposits are seen, use a high pressure garden hose to flush the scale off.

When should you Clean a salt cell?

When to Clean the Salt Cell Beyond pool opening and closing, it’s a good idea to check on your salt chlorine generator once a month during the height of swimming season. The frequency of your cleaning and maintenance schedule will be dependent on pool use, water hardness, pool chemistry and the age of your salt cell.

What causes calcium buildup on salt cell?

What causes scale buildup in a salt cell? The salt cell’s ECG can provide a perfect breeding ground for two reasons: heat and high pH production. Heat — The hotter the water, the more calcium tends to drop out of pool chemical solutions and mineralize into a deposit.