How do you use a Waterlox butcher block

Waterlox finishes tend to wear very nicely and settle into a nice patina. They also will maintain a high level of protection even when worn (to a certain degree) due to the penetrating nature of the coatings. In general, the lifespan of an interior coating on a well-used surface will be 7-10 years.

How long does Waterlox last on butcher block?

Should I sand between coats of Waterlox?

Sanding for adhesion purposes is not required between coats of Waterlox Original Tung oil finishes. … With Waterlox Original Tung oil finishes, new coats will actually bond with the previous Waterlox coat and becomes part of it rather than a layer on top of it.

How many coats of Waterlox should I use?

Waterlox recommends at least three coats for most species of wood, sometimes four for soft woods like fir or pine. Keep your applicators literally submerged in paint thinner in between coats – if they dry out they tend to get crusty and useless.

How do you prepare wood for Waterlox?

Lightly sand the surface with a synthetic abrasive pad (medium/maroon recommended). If sanding, lightly dampen a mop, lint-free rag or micro-fiber mop with water or regular mineral spirits1 (paint thinner) to remove dust. Allow to evaporate 30–45 minutes (until dry appearance) before applying Waterlox ORIGINAL Finish.

What temperature do you apply Waterlox to?

During application of Waterlox wet-applied finishes (ORIGINAL, H2OLOX®, URETHANE or MARINE), the product, project surface and environment should be close in temperature and at least 50°F during application and at least 1-2 hours afterward. When both the product and surface are cold, they are less compatible.

Is Waterlox good for butcher block countertops?

Wood countertops can give your kitchen, bath or bar an unprecedented look. Waterlox is a superb choice for finishing wood countertops because it produces an incredibly appealing and durable surface. It is waterproof, food-safe and easy to maintain.

How long does it take for Waterlox to cure?

Allow each and every coat to dry for 24 hours. Dry time will depend upon ventilation, humidity and temperature. CURING Even though the recommended dry time is 24 hours, Waterlox Original Tung oil finishes completely cure in 30 – 90 days.

Do you wipe off Waterlox?

Clean up. Wipe the surface clean with a clean lint free cloth, very lightly dampened with mineral spirits. … If you are going to leave your project as finished at this point, it is best to start with an extra coat because you are going to remove some extra material.

Does Waterlox dry hard?

All Waterlox coatings will cure through exposure to oxygen. … When a Waterlox coating is staying soft, tacky, or has a lingering odor, this is a sign that the oxygen is having a hard time curing all of the oil.

Article first time published on

Can I apply Waterlox with a rag?

So I’ve applied waterlox a few times now. I’ve found the most foolproof way to apply is a rag/cheesecloth, but the buildup takes significantly longer, not to mention the occasional lint or fuzz that gets caught on the grain. The recommended way to apply it is with a brush.

Is Waterlox easy to apply?

Why use Waterlox Repairing a damaged finish also is also very easy when using Waterlox. The wood surface can be simply be cleaned and another coat can be applied at anytime.

What is the best way to apply Waterlox?

Apply Waterlox ORIGINAL Sealer/Finish liberally with the grain using a lamb’s wool applicator (floors) or a quality natural bristle brush or paint pad. Allow to dry for 24 hours. Repeat steps 2-4 for a second (for soft wood species, a third) coat.

Does Waterlox change the color of the wood?

Stain should only be mixed into the first coat of Waterlox sealer. This should be used as the base coat. Additional tinted layers can be used, but they may not color the wood as desired.

How do I remove a Waterlox finish?

Razor blade knife;
Acetone (nail polish remover); and/or.
Chemical Paint Stripper.

Is Watco butcher block oil Food Safe?

Watco® Butcher Block Oil + Stain is specially formulated for use on wooden butcher blocks, cutting boards, salad bowls and other wood applications which require a food safe finish. Easy to apply and maintain, it is nontoxic and safe for food contact when fully dried (meets government standards of 21CFR 175.300).

What finish do you put on a butcher block?

Our standard finish on butcher block cutting boards, chopping blocks and specialty boards is mineral oil. Mineral oil has been the traditional finish used by butchers for over a century to keep their blocks looking and functioning at their best.

Do you need to seal both sides of butcher block?

You will need to finish all surfaces (top, bottom and sides) of your unfinished butcher block or wide plank top with a commercial grade polyurethane or Waterlox finish. Follow manufacturer’s instructions on the polyurethane or Waterlox for finishing coats (usually three or four coats).

Is Watco butcher block oil waterproof?

Bottom line. The wood is totally waterproof. The water just beads up on top. Now I am not planning to just leave water puddling on top for days or weeks, but I do think that if you just wipe off any excess water after doing dishes this product is excellent.

How do you clean a brush after using Waterlox?

Pour about 1 inch of paint thinner (mineral spirits) into one of the containers. Insert the brush into this container and press out the bristles into the thinner. Varnish will be released into the thinner. Pour the contaminated varnish/thinner mixture into the other can.

How often do you have to seal Butcher block countertops?

While butcher block countertops do require routine maintenance, resealing the surface is only required after every 6-12 months depending on the level of use. The same goes for natural stone countertops, which must be resealed over time to maintain the original quality and look.

When can you walk on Waterlox?

The first 7 days are the most critical after applying Waterlox Original Tung oil finishes. Please adhere to the following practices: After the last coat is applied, we advise staying off the surface for at least 24 hours. After this time, if you are finishing a floor, it may be used for sock traffic only.

Can tung oil be applied in cold weather?

Do not apply when air or surface temperature is below 50°F. Do not apply over wet or damp surfaces. Do not thin or add colorant to this product.

Does Waterlox yellow?

Waterlox is a very yellow tinted finish. That said, a yellow tint is generally used for Walnut. The yellow brings out the color and grain of the wood.

Can you sand off Waterlox?

Sanding is not required, but removal of damaged, cracked, peeling or scratched film is recommended. Final sand should be with 0000 steel wool, 320 grit sandpaper or a maroon pad before recoating. A second coat of finish may be needed in areas where bare wood was exposed.

Is Waterlox a varnish?

And Waterlox is varnish, specifically a phenolic resin/tung oil varnish.

Is Waterlox safe for food?

Waterlox ORIGINAL finishes are water resistant, stand up to household spills and are non-toxic and food-safe when dry. Waterlox Original Tung oil finishes have good heat resistance, can be used around stoves and are unaffected by boiling water and liquids.

Can you thin Waterlox?

H2OLOX can be thinned with water, but it is never recommended to do so. You can also use water between coats of Waterlox to pick up stubborn dust. DO NOT soak the floor, but use a lightly dampened, lint-free rag and allow plenty of time for the water to evaporate before applying the next coat.

Is Waterlox better than tung oil?

While Waterlox Original Tung oil finishes contain a superior drying oil, namely Tung Oil, they are fully cooked varnishes, which dry quicker and form permanent films tough enough to walk on and take daily abuse. Waterlox Original Tung oil finishes are also water and chemical resistant (alcohol and alkali).

Is Waterlox a gloss?

Waterlox Oil-Modified Urethanes use a very high quality urethane base that is modified with soya oil. This resin system is naturally high gloss, so flattener is added to lower the gloss to satin and semi-gloss levels.

How do you use Waterlox high gloss?

Waterlox Original High Gloss Finish Product Uses For best results, apply all coats liberally at approximately 500 square feet per gallon per coat. No thinning necessary. Clean application tools immediately with mineral spirits or turpentine.