How do I reset my Ferroli Optimax boiler?
How do I reset my Ferroli Optimax boiler?
Press heating + and p02 appears. Press hot water + and 0 codes appear. Then press up or down on heating + or – to get o1 . Then press reset for ten seconds.
Why won’t my Ferroli boiler fire up?
If your Ferroli boiler is only igniting briefly, or making a ‘puffing’ sound, this is usually down to flue problems, such as corrosion in the flue duct, or joints coming lose. The Fix: Get an engineer to replace your flue or clamps holding the flue in place.
What pressure should my ferroli boiler be?
between 1.0 and 2.0
Your boiler gauge should show that the boiler pressure is between 1.0 and 2.0. If the pressure drops below 1.0, then you’ll need to repressurise it.
What causes high boiler pressure?
Boiler pressure is controlled by the expansion vessel, the balance of air versus water in your central heating system. Too little air in your expansion vessel and the pressure may become too high. resulting in the water coming out of your pressure relief valve.
Why is my boiler flashing FH?
FH Error Code: FH can be one of two things, the flame detection electrode or a faulty PCB – you’ll need a boiler engineer but the later of the two is an expensive fix! You should check your gas supply and reset the boiler, but if the problem persists you will need to call a boiler engineer.
What temperature should my ferroli boiler be set at?
Heating temperature adjustment of 30°C to a max. of 80°C; in any case, it is advisable not to operate the boiler below 45°C.
Why does my ferroli boiler keep losing pressure?
Ferroli Boiler Fault 3: Pressure Loss and Lockouts Leaks are the most common cause of a pressure loss fault. Most of the time this will be leaking from radiator valves, or valves on towel rails. However, the leak can sometimes come from the auto air vent in the boiler, or expansion vessel.
How long should a Ferroli boiler last?
between 1-10 years
Ferroli Boiler Warranty Every boiler manufacturer offers a standard warranty with their boilers which last between 1-10 years.
What should the temperature of a Ferroli boiler be?
Temperature can be varied from a minimum of 30°C to a maximum of 85°C. It’s advice for the boiler to operate above 50°C. The thermal head is the temperature difference between the delivery water and return water in the central heating circuit).
How much does it cost to fix a Ferroli boiler?
However, they are only sold as a pack which costs over £120 at trade price, so it could be an expensive fix!
What kind of boiler does Optimax he plus 38 C use?
OPTIMAX HE PLUS 38 C is a high-efficiency condensing pre-mix appliance for heating and hot water production with extremely low emissions, running on natural gas or LPG. The boiler consists of an aluminium laminar heat exchanger providing effective condensation of the water vapour contained in the flue gases, permitting extremely high efficiency.
What should I do if my Ferroli boiler goes into lockout?
In the event of the red lockout light coming on, the on/off/reset switch should be turned clockwise against the spring tension to the reset position and released. Boiler will go into three minute delay if in the heating mode.
Temperature can be varied from a minimum of 30°C to a maximum of 85°C. It’s advice for the boiler to operate above 50°C. The thermal head is the temperature difference between the delivery water and return water in the central heating circuit).
However, they are only sold as a pack which costs over £120 at trade price, so it could be an expensive fix!
OPTIMAX HE PLUS 38 C is a high-efficiency condensing pre-mix appliance for heating and hot water production with extremely low emissions, running on natural gas or LPG. The boiler consists of an aluminium laminar heat exchanger providing effective condensation of the water vapour contained in the flue gases, permitting extremely high efficiency.
In the event of the red lockout light coming on, the on/off/reset switch should be turned clockwise against the spring tension to the reset position and released. Boiler will go into three minute delay if in the heating mode.
