Can you replace a 10-inch rough in toilet with a 12-inch rough in toilet?

Can you replace a 10-inch rough in toilet with a 12-inch rough in toilet?

Ideally, the toilet’s rough-in should match the rough-in for your bathroom plumbing. However, even if a toilet is designed for a 10-inch rough-in, you can still install it into a space that has a 12-inch rough-in.

Can you replace a 14-inch rough in toilet with a 12-inch rough in toilet?

Replace a 14-inch rough-in toilet with a 12-inch rough-in toilet. You can definitely replace a toilet with a rough-in of 14 inches with one with a rough of 12 inches. The problem with this method is that a 2-inch gap will be left between the toilet tank and the wall.

How do you install a toilet in new construction?

How to Install a Toilet in New Construction

1. Cut the soil stack with a hacksaw if necessary so it is even with the finished surface of the floor.
2. Place the closet flange onto the drainpipe.
3. Remove the closet flange.
4. Fasten the closet flange to the floor with stainless steel screws.

How far off the wall should a toilet be?

Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.

Why would I want an elongated toilet bowl?

Elongated bowls are also considered more ‘hygienic’ in that the larger surface area of the bowl makes is easier for men and children to use with less mess. The longer bowl size is also a requirement for ADA use, and the longer/wider bowl is generally easier to use for those with mobility issues.

Can you replace a 13 inch rough in toilet with a 12 inch rough in toilet?

Though the standard rough-in size is 12 inches, most of them are not exactly 12 inches. So, if you install such a toilet on a 13 inch rough-in, you’ll only have a gap of 1-inch between the tank and wall. So far, I’ve found only one 12 inch rough in toilet model that can be great for 13 inch rough in sizes.

Does a toilet have to be against a wall?

No, there is no standard distance a toilet tank should set out from the wall. There are standard rough in distances, the most common is 12″ with a few at 10″ and a few at 14″, but the actually distance the tank will be from the wall will vary. Yours is quite normal.

How do you put in a new toilet fill valve?

1. Insert the bottom of the new fill valve’s stem through the opening in the bottom of the toilet tank. 2. Position the valve so the water outlet is pointed toward the toilet overflow tube. 3. Holding the valve in place with one hand from above, use your other hand to put the metal washer and mounting nut on the tailpiece of the valve. 4.

How do you install a toilet stop valve?

Find an adjacent wall stud and secure the copper water piping to it with an insulated pipe hook. One alternative is to solder the line to a copper nailing strap that is secured to the wall studs on either side of the water line. Install your toilet stop valve and a trim ring to the end of a ½-inch copper water line stub-out.

What do you need to know before roughing in a toilet?

You need to know 4 things before roughing-in a toilet: The distance to set the toilet flange from the back wall. The necessary clearance from left to right. How much space to leave in front of the bowl. Where to put the cold water supply line. And it’s pretty important to get these measurements right…

How to install new plumbing lines for a toliet?

Reduce the size of the opening of the top of the soil stack to 2 inches with a reducing coupling. Glue 2-inch PVC pipe to the reducer and extend it through the roof. This pipe vents the toilet and should terminate 1 foot above the roof line.

Find an adjacent wall stud and secure the copper water piping to it with an insulated pipe hook. One alternative is to solder the line to a copper nailing strap that is secured to the wall studs on either side of the water line. Install your toilet stop valve and a trim ring to the end of a ½-inch copper water line stub-out.

You need to know 4 things before roughing-in a toilet: The distance to set the toilet flange from the back wall. The necessary clearance from left to right. How much space to leave in front of the bowl. Where to put the cold water supply line. And it’s pretty important to get these measurements right…

Reduce the size of the opening of the top of the soil stack to 2 inches with a reducing coupling. Glue 2-inch PVC pipe to the reducer and extend it through the roof. This pipe vents the toilet and should terminate 1 foot above the roof line.

What’s the best way to replace a toilet?

Here’s an overview on how to remove an existing toilet for replacement: Turn off the water at the shut-off valve located either on the wall or floor near the toilet. Flush the toilet to drain all the water from the tank and toilet bowl. Use a plunger to force any remaining water down the drain line.