Can you buy just the top of a toilet?

Can you buy just the top of a toilet?

Because the tanks and bowls may be sold separately, you can often buy just the tank. However, it is important to match the toilet manufacturer and model to ensure proper installation and function of the toilet when you’re done. Drain the water from the bowl and the tank by flushing the toilet.

Are toilet tank lids interchangeable?

Toilet Tank Lids Tip: Because toilet tank lids are made from clay, then high fired in a kiln, each one will be a little different than all the others. No two toilet tank lids are exactly alike.

How do I find the right toilet tank lid?

Look for the manufacturer name or a number on the bottom side of the water tank lid. It may be stamped into the lid or painted on – some of them may even be handwritten if the tank lid was replaced by a plumber with foresight.

What is the standard size of a toilet tank?

Tanks come in a few different sizes, and one of them is small. Small tanks vary in size; however, one standard length is 15 1/8 inches. It is common to see these tanks on toilets with bowls and seats of a similar size.

Is it possible to read the model number on a Kohler toilet?

Model numbers in older toilets may be hard to read due to mineral or bacterial growth within the tank. Rub the area to remove residue. Refer to care and cleaning for vitreous china toilets and bidets on In some KOHLER tanks, an Insuliner® tank liner may be installed, covering the model number.

How to troubleshoot a Kohler dual flushing toilet?

Corrective Actions: 1 Check the trip lever chain for excessive slack. 2 For dual flushing toilets, verify that the rod length is correct. 3 Verify that the hose is properly connected to the top of the canister. 4 Verify that the water level meets the marked waterline. 5 Clean the rim holes under the bowl rim.

What do you call a standard Kohler toilet tank?

Use only KOHLER Genuine Parts to avoid property damage and achieve optimal performance. The phrase “Standard Toilets” applies to floor-mounted toilets with standard flush and fill valves and dual flush models. Refer to In-Wall Toilet Tank Troubleshooting if you have an in-wall toilet tank.

How to replace the fill valve on a Kohler toilet?

1 Partially close the water supply shut-off valve. 2 Check the fill valve for debris, and clean as needed. 3 Make sure the rim feed hose (if equipped) is connected to the overflow and fill valve. 4 Replace the fill valve with a genuine KOHLER fill valve for optimal performance.

What kind of GPF does Kohler persuade toilet have?

The Persuade collection captures the essence of modernity in subtle curves and clean lines. With its sleek symmetry, this 2-piece Persuade Curv toilet adds style to the bathroom without sacrificing water savings. The 2-button flush offers the choice of 1.0 GPF or 1.6 GPF.

What is the model number on a Kohler one piece toilet?

In some cases, the model number is preceded by 97 or F. For example, 974166 contains the model number 4166, and F4166 contains the model number 4166. One-piece toilet: The number inside the tank is the primary toilet model number. Two-piece toilet: The number inside the tank is specifically for the tank (the bowl has its own model number).

What’s the difference between 1.28 gpf and 1.6 gpf toilets?

In 1995, the National Energy Policy Act started requiring plumbing manufacturers to make and homeowners who were remodeling their homes to purchase toilets that utilized 1.6 gallons of water per flush or less. If you’re undecided about which toilet to choose between the 1.28 GPF and 1.6 GPF toilets,…

Why are Kohler toilets so hard to clean?

Functions well but. . . Kohler does not seem to be alone in their current design of toilets. Instead of a smooth exterior which was the way most all toilets were designed, including the most inexpensive models, they’ve all gone to molded bases with too many convolutions, indentations and hoes. This make cleaning very difficult and unsanitary.